• Villacryl H Plus Liquid 400 ml

Villacryl H Plus Liquid 400 ml


  • 5500 lei

  • Fără TVA: 4622 lei
Producător: EVERALL7
Cod produs: 201688
Disponibilitate: În stoc

Description

Villacryl H Plus heat-curing acrylic resins, intended for denture bases, removable full or partial prostheses and for the indirect relining of removable prostheses.

• Heavy metals free
• Biologically neutral
• High mechanical strength
• Comes in 5 colors: transparent (0), milk pink veined (V2), dark pink veined (V3), pink veined (V4) pink (T4)




    Villacryl H Plus - Acrylic material for hot curing. Designed for the manufacture of bases for removable dentures.

     

    APPLICATION

    • Complete removable dentures
    • Removable partial dentures

      

    ADVANTAGES

    • High comfort of using prostheses
    • High aesthetics thanks to natural colors
    • High color stability
    • Does not contain heavy metals
    • High mechanical stability
    • Low polymerization shrinkage
    • Ease of processing
    • Plastic consistency during placement in the polymerization flask
    • Doesn't stick to hands

    Ease of use. Simple kneading process, easy processing and polishing. In the process of manufacturing the prosthesis, the material has a plastic soft consistency and does not stick to the hands. After polymerization, it is characterized by high strength, while being easily processed and polished.

    Aesthetics. Five colors for the most accurate selection: T4 (pink), V4 (pink veined), V2 (milky pink veined), V3 (dark pink veined), O (clear).

    Plastic Villacryl

    For prostheses made of Villacryl H Plus and Villacryl H Rapid FN, both relining and the use of soft silicone pads are possible.

    High color stability.

    Plastic Villacryl

    Bio-neutral.

    Does not contain heavy metals.

     INSTRUCTIONS FOR USE

    Villacryl H Plus (Villacryl Ash Plus) is a hot curing acrylic dental material for the manufacture of removable denture bases.

     GENERAL INSTRUCTIONS

    • Do not use in patients who are allergic to the ingredients included in the composition of the material.
    • Before installation, the prosthesis should be disinfected.
    • Warn the patient that if proper hygiene is not observed, irritation and inflammation of the oral cavity may occur.
    • Application (one option)

     

    PREPARATION

    • Glue the wax model of the prosthesis on the base using wax. Align the attachment point.
    • Mix hard dental plaster. Fill the bottom of the cuvette 2/3 with plaster. Put the model in it. Smooth out the plaster and leave to harden. After hardening, smooth the surface of the gypsum under water.
    • Coat the model with C-silicone. Do not apply silicone to the chewing surfaces of the teeth and to the cutting edges. Wait for the silicone to bind.

    Plastic Villacryl

    • Place the cuvette in water for 10-15 minutes. Take out. Install the second part of the cuvette and completely fill the model with plaster. After the gypsum has hardened, place the cuvette in boiling water to soften the wax.
    • Remove the cuvette, free the model from wax.
    • Apply an insulating material (Izo-sol) to the top of the plaster impression, spread over the surface and rinse with water.
    • Release the silicone impression from the teeth. Lightly work the surface of each tooth with a bur to roughness, use a cutter to make notches in the lower part of the teeth. Set your teeth in place. Apply bond to the surface of the teeth.

    Plastic Villacryl

     

    PREPARING PLASTIC

    • Place the required amount of monomer and resin into a glass vessel. Mix thoroughly with a metal spatula and leave covered. The ingredients are taken in the following proportion: for 24 g of powder / 10 g of liquid. When the mass stops sticking to the walls of the container, it should be removed and kneaded with your fingers for 1-2 minutes.

    Plastic Villacryl

     

    FILLING AND POLYMERIZATION

    • The finished plastic should be placed into the silicone mold by gently distributing it with your fingers. After that, the plastic is covered with a plastic film; they install the second part of the cuvette. The cuvettes are placed in a hydraulic press for 15 minutes (pressure 5000 kg).
    • Remove the cuvette from the press, separate the parts, remove the film and remove excess plastic with a spatula and connect the parts. Put the cuvette under the press again.

    Plastic Villacryl

    • Place the cuvette in the frame and place in the polymerization chamber. The polymerization time depends on the size of the prosthesis.
    • Polymerization is carried out in water at a temperature of 65°C under a pressure of 2 bar. The polymerization time is 20 minutes.
    • After cooling, the prosthesis is removed from the cuvette.

    Plastic Villacryl

     

    TREATMENT

    • The finished denture should be ground with a burr and polished with polishing powder and polishing paste.

    Plastic Villacryl


Distrident recomandă Vezi toate

Ceara de modelat SOFT 60 gr. ivory opac
DISTRIDENT PLUS
Fabricat în RO

Ceara de modelat SOFT 60 gr. ivory opac

2700 lei

Ceara tije HARD
DISTRIDENT PLUS
Fabricat în RO

Ceara tije HARD

1950 lei

Gips clasa 5 SUPER PREMIUM - 5 kg
DISTRIDENT PLUS
Fabricat în RO

Gips clasa 5 SUPER PREMIUM - 5 kg

16900 lei

Gips clasa 4 PREMIUM - 10 kg
DISTRIDENT PLUS
Fabricat în RO

Gips clasa 4 PREMIUM - 10 kg

21900 lei

Gips clasa 4 PREMIUM - 5 kg
DISTRIDENT PLUS
Fabricat în RO

Gips clasa 4 PREMIUM - 5 kg

12700 lei

Comandă telefonică

Răspundem prompt! Sună-ne dacă ai nevoie de ajutor pentru a comanda de pe site-ul nostru.

Livrare în 24h

pentru comenzile date până în ora 12:00, în zilele lucrătoare, exceptând perioadele aglomerate de Sărbători legale.

Plătești în siguranță

Acceptăm plata online cu cardul bancar sau poți achita coletul în momentul livrării.

Retur ușor

Ai dreptul să returnezi produsele în termen de 14 zile calendaristice de la primirea coletului.